The Apogee system issued a critical system message.

 

The job has stopped pending user interaction.

 

The job has generated an error, and has stopped.

 

The job has generated a warning.

 

WebApproval remark: A remark on this job (or results) has been received from WebApproval.

 

The job has generated an information message.

 

The job is being archived or dumped.

 

The job is being imported from archive.

 

The job is being deleted.

 

Apogee is queuing all commands for this job.

 

The document is being edited (it is ‘checked out’).

 

The job is being edited by another user.

 

The Run List is being edited by another user.

 

You are editing the job.

 

You are editing the Run List.

 

The job is finished.

 

The job was broken during editing. You can remove this icon by opening the job for editing.

 

The job has been manually put on hold.

 

The job output is waiting for the correct media to be loaded on the output device.

 

The job is waiting for a Task Processor (none currently available).

 

A group of results is complete, and is waiting to be printed (blue icon).

 

The result is waiting for a hard proof.

 

The result is waiting for a web proof.

 

The job is waiting for a soft proof.

 

A task has been aborted.

 

The task has been manually put on hold.

 

New (unplaced) documents are available in the (Private) Page Store.

 

The job is waiting for results.

 

Not all the results of a group are yet available (green icon).

 

The job is waiting for After Hours processing.

 

Some results have been rejected by the user.

 

The layout/imposition is not yet defined.

 

The job has reached a Milestone: The Run List is not complete. This Milestone was set up in the Options tab.

 

The job has reached a Milestone: The job deadline has been reached. This Milestone was set up in the Options tab.

 

The job has reached a Milestone: The result is not available in time. This Milestone was set up using a Milestone Action in the Production Plan.

 

The job is managed by PlateMaker (ready to plate). The PlateMaker client will take care of further plate production.

 

A job that has been merged

 

A merged job: The job resulting from the merging of two or more other jobs.

 

Job is a recurring job.

 

A StoreFront job: The job was generated by StoreFront.

 

The job is being viewed by you or by another user (JTE only).

 

The job is being edited by another user.

 

You are editing the job.

 

The selected job was being edited by you or by another user, but the edit session was broken (Jobs window only). You can remove this icon by opening the job for editing.

 

The job has remarks.

 

Job group.

 

Commercial job with incomplete Run List.

 

Commercial job with complete Run List.

 

Rush job (Commercial jobs only).

 

Commercial job with disabled input channel.

 

Commercial job is scheduled to be archived when it is finished (Options tab).

 

Commercial job has been archived.

 

Commercial job is scheduled to be deleted when it is finished (Options tab).

 

Commercial job has been deleted.

 

Commercial job is scheduled to be archived and deleted when it is finished (Options tab).

 

Commercial job has been archived and deleted.

 

Commercial Hot Ticket.

 

Commercial Hot Ticket with a disabled input channel.

 

Job that requires set-up by Printer (WebApproval jobs only)

 

Collecting Hot Tickets (tickets grouped in separate panel)

 

Main Output to a high resolution output device.

 

Main Output to a Sign and Display output device.

 

Imposition Proof: An optional flow which may be added to the Main Output flow, and is used for output to an imposition proofing device.

 

Page Proof: An optional flow which may be added to the Main Output flow, and is used for output to a page proofing device.

 

Export: An optional or alternate flow to the Main Output flow, used for exporting job results to file in PDF or PostScript format.

 

Public Page Store: An optional or alternate flow to the Main Output flow, used for storing job results in a Public Page Store.

 

Display: An optional or alternate flow to the Main Output flow, used to create job results for high-resolution soft proofing.

 

Digital Quick Strip (DQS): An alternate mode of operation which supports the PrintDrive DQS mode of Apogee Series3. In this mode, Apogee creates and renders the flat backgrounds and pages separately. These are then sent as separate items to PrintDrive. PrintDrive assembles the pages onto the backgrounds, and then outputs the results as an integral job.

 

Collecting Hot Ticket: Uses the Collect TP to collect images and create special Hot Tickets.

 

A white background color indicates that this flow is idle.

 

A green background color indicates that this flow is currently active.

 

A blue background color indicates that this flow is on hold.

 

A yellow background color indicates that this flow contains tasks which are queued and waiting to be processed.

 

A white background color with a green checkmark indicates that this flow has finished.

 

A red background color indicates that this flow has generated an error.

 

A purple background color indicates that further handling of this flow has been taken over by PlateRunner (Main flow only). For more details, refer to the PlateRunner documentation.

 

Job Filter not applied.

 

Job Filter applied.

 

Discard

 

Wait for Results

 

Web Proof

 

Soft Proof

 

Hard Copy Proof

 

Collect for Output

 

After Hours

 

Keep Result

 

Archive Result

 

Notify

 

Milestone

 

PDF / PostScript composite document.

 

PDF / PostScript composite page.

 

PDF / PostScript pre-separated document.

 

PDF / PostScript pre-separated page.

 

Raster composite document.

 

Raster composite page.

 

Raster pre-separated document.

 

Raster pre-separated page.

 

A red-colored icon indicates that the document or page has been processed with errors.

 

An icon with a red stripe indicates that the document or page has been rejected.

 

A blue-colored icon indicates that the document or page is on hold.

 

A Public Page Store (Page Store only).

 

Empty placeholder (Run List only).

 

Blank page (Run List only).

 

Job processing is not yet complete in the Production Plan before the Run List.

 

Unknown document.

 

Page imposition has been adjusted (Run List only).

 

(in Run List status column of normal job). The page has a preflight report. Clicking on the icon will open the report in your PDF viewer.

 

(in Run List status column of versioning job). One or more pages in this row have a preflight report. Clicking on the icon will bring up a menu which contains the titles of the objects to which the preflight reports are attached. Selecting one of the menu items opens the report in your PDF viewer.

 

(in Run List status column of job). The page has generated a preflight error. Clicking on the icon will open the Problem Report.

 

(in Run List status column of job). The page has generated a preflight warning. Clicking on the icon will open the Problem Report.

 

PDF is certified.

 

PDF is not certified.

 

Document is being edited interactively within Apogee using the Check-Out plug-in for Acrobat or any other PDF Viewer/Editor application such as the Amfortis Editor.

 

Document has been edited interactively within Apogee using the Check-Out plug-in for Acrobat or any other PDF Viewer/Editor application such as the Amfortis Editor.

 

Document page size does not match the page trim size set for the product or part.

 

A single PDF layer from a page, without errors.

 

A single PDF layer from a page, with errors.

 

A single PDF layer from a page, on hold before reaching the Run List.

 

A single PDF layer from a page, which has been rejected.

 

A full bar indicates that one or more of the side versions to which this page contributes will have a full set of plates made.

 

A half full bar indicates that one or more of the side versions to which this page contributes will have a partial set of plates made.

 

An empty bar indicates that none of the side versions to which this page contributes will have any plates made.

A thumbnail view of this page is either not available, or is currently being retrieved from the Apogee System (green background color).

Page has been processed successfully (no background color).

Page has been processed successfully, and is on hold pending approval (blue background color).

Page has been processed with errors (red background color).

Page is managed by the PlateMaker Client, and is ready to plate (purple background color).

Page has been processed successfully, but has been rejected.

Page has been discarded.

An empty page in the Run List (white background with a cross).

A blank page in the Run List (white background).

 

The page/flat belongs to a proofing workflow or a layout job, and is a composite file (i.e., not a separation). The page/flat has been rendered, and is ready for output.

 

The page/flat belongs to a proofing workflow or a layout job, and is a composite file (i.e., not a separation). The check mark indicates that it has been successfully printed.

 

A square gray-colored indicator in the lower right corner of the page indicates that all separations have been fully rendered and are ready for previewing or output. Visible for DQS and Raster Impose results when you choose View > Show > Page Rendered.

 

A small fold in a corner of a page indicates the orientation. The position of the fold tells you where the top of the page is.The orientation of a page may vary in an imposition layout.

 

The job or flow is finished.

 

The job’s Production Plan contains an After Hours Action. When this point is reached, the job results are held (written to disk) pending the specified time.

 

The job’s Production Plan contains a Soft Proof Action. When this point is reached, the job results are held (written to disk) pending approval/rejection of a Digital Film preview by the user.

 

The job’s Production Plan contains a Hard Copy Proof Action. When this point is reached, the job results are held (written to disk) pending approval/ rejection of a hard copy proof by the user.

 

The job’s Production Plan contains a Ready for Plating Action. When this point is reached, the job results are taken over and managed by PlateRunner (ready to plate).

 

The job’s Production Plan contains a Collect for Output Action. When this point is reached, the job results are held (written to disk) pending user intervention.

 

The job’s Production Plan contains a Waiting for Results Action. When this point is reached, the job results are held until the target flow or required pages are finished.

 

The job’s Production Plan contains a Discard Action. When this point is reached, the job results are held until the specified pages have been automatically discarded.

 

The job’s Production Plan contains a Web Proof Action. When this point is reached, the job results are held (written to disk) pending approval/rejection of a Digital Film preview by the remote user.

 

Result will be frozen once it has been approved by the remote user.

 

Result has been frozen because it has been approved by the remote user.

The page or flat has not yet reached this Action.

The page or flat has reached this Action (blue background).

The page or flat has passed this Action (dimmed icon).

 

Square outlined separation indicator:

 

Square solid separation indicator: A process color separation has been rendered, and is ready for output. In this example, it is the magenta separation.

 

Checked separation indicator: The separation has been rendered, and has been successfully output. In this example, it is the magenta separation.

 

Dimmed separation indicator: The separation has been discarded, and will not be output.

 

Round outlined separation indicator: A spot color separation is expected (it has not yet been rendered). The outline color is the color of the expected spot color.

 

Round solid separation indicator: A spot color separation has been rendered, and is ready for output. The solid color is the spot color.

 

Checked separation indicator: The spot color separation has been rendered, and has been successfully output.

 

Process colors known but not rendered (round separation indicators for spot colors).

 

Process color plates from this version to be output (round separation indicators for spot colors).

 

Process color plates from other version to be remade for this version (round separation indicators for spot colors).

 

Process color plates from other version reused, but not remade (round separation indicators for spot colors).

 

Process color plates from this version made (round separation indicators for spot colors).

 

Process color plates from reused (but not remade) version output (round separation indicators for spot colors).

 

Full bar at the side of the box: A full set of plates will be made for this side.

 

Half bar at the side of the box: A partial set of plates will be made for this version.

 

One or more version pages used by the side is not yet available (empty placeholder).

 

The background and all version pages used by the side are available, but the render data for the whole side is not yet complete.

 

All render data for the side is available, but not all plates have yet been produced.

 

Finished state: All plates for the side have been produced.

 

Error state: Processing of this side has been stopped by an error.

 

On Hold state: Processing of this side is waiting at a hold point.

 

This side or one of its separations or pages has been rejected.

 

This side has been discarded and will not be processed further.

The color definition was found in the Apogee Color Books.

The Emulate Overprint option is always on.

The Emulate Overprint option is always off.

The Emulate Overprint option is selected automatically.

The color contains version-specific content.

The color does not contain version-specific content.

The color was found in the job.

The color was manually entered.

The color was manually entered and was found in the job.

The color is directly linked to the selected color

The color is indirectly linked to the selected color.

The color was found in the border or the imposition template.

The color was manually entered, with marks.

Mapped color name as defined by the Pantone mapping settings.

Special color: corresponds with an operation other than the contour-defining one.

Special color: varnish.

Special color: die line.

Special color: other.

Indicates that this section is part of a multiple-section signature.

 

The monitor status is up to date and the overall display rating is equal or greater than 90% (Excellent).

 

The monitor status is up to date and the overall display rating is between 80% and 90% (Medium).

 

The monitor status is up to date and the overall display rating is less than 80% (Bad).

 

There is no monitor status, or it is out of date (Undefined).

 

Customer remark (WebApproval jobs only).

 

Printer remark (WebApproval jobs only).

 

An annotation remark created in WebApproval. Click the associated (blue -encircled) annotation number to jump directly to the referenced location in Raster Preview.

 

The job has been approved by the corresponding reviewer (printer, customer).

 

The job has been rejected by the corresponding reviewer (printer, customer).

 

A job remark.

 

A page remark.

 

Preflight remark

 

Preflight remark - warning

 

Preflight remark - error

 

Internal remark which cannot be seen by the customer

 

Remark has attachment (customer remarks only)

 

View file produced after preflight

 

View report produced by preflight

 

The Task Processor is ready, and is currently idle.

 

The Task Processor turns green when it is processing a task. For example, the Avantra Task Processor is busy processing a separation.

 

The Task Processor turns red if a processing error occurs. In this case an error notification is sent to the Message Board, explaining the nature of the error.

 

The Task Processor turns blue if it is offline.

 

When the Task Processor has been stopped (inactive), the icon will have horizontal stripes running through it. You can re-activate it by context-clicking on the icon and selecting Start from the context menu.

 

The Task Processor is starting up (moving horizontal stripes).

 

The Task Processor is locked, because you do not have a license to use it.

 

A purple arrow is attached to the Task Processor icon if:

 

Paused: The output engine is able to communicate, but cannot process any tasks. A user interaction has taken place on the device itself to trigger this status.

 

Disconnected: The output engine's cable has been unplugged.

 

Warning: The hardware engine requires attention (e.g. ink low), but can still receive tasks.

 

This platesetter is managed by PlateRunner. The yellow ‘sun’ patch indicates that the device is in attended state (i.e. A user is logged in to the PlateRunner application).

 

This platesetter is managed by PlateRunner. The gray ‘moon’ patch indicates that the device is in unattended state (i.e. no one is logged in to the PlateRunner application).

 

Error: The hardware engine requires attention - it cannot continue to receive and process tasks until the problem has been resolved (e.g. no ink).

 

Media: The icon is followed by a name: There is a cassette in the tray but it is not loaded (not active). However, it can be activated by Apogee. If the name is in bold, the cassette is loaded (active).

 

Media: The icon is followed by a name: There is a cassette in the tray but it is not loaded (not active). However, it cannot be activated by Apogee (manual intervention on the engine is required).

 

Media: There is no cassette in the tray.

 

Media: There is an unknown problem with the tray.

 

Dedicated Resource linked uniquely to a specific device: This Resource is not shared between other devices of the same type.

 

Archived Commercial job (.arch)

 

Archived Public Page Store job (.arch)

 

Saved Commercial Job Ticket(.ajt)

 

Saved Commercial Hot Ticket(.aht)

 

Submit job or submit changes to a job.

 

Delete the selected item.

 

Edit job.

 

View <selected item> (Job Ticket Editor only).

 

Make Blank (page in Run List - Job Ticket Editor only).

 

Give priority to processing the selected job (Rush job).

 

Hold job, or put device offline (System Overview).

 

Resume a job on hold, or put device online (System Overview).

 

Continue processing <selected item>.

 

Reject <selected item>.

 

Reprocess job from first.

 

Re-image <selected item>.

 

Enables the selected Hot Ticket (Hot Tickets window only).

 

Disables the selected Hot Ticket (Hot Tickets window only).

 

Display information about <selected item>.

 

Marquee tool. Allows you to draw a rectangle in the Preview window by clicking and dragging. The ink values for the selected region are measured and displayed in the Inks palette.

 

Hand tool. Pans the image, allowing you to view a page that exceeds the size of the Preview window. With this tool selected, click inside the Preview window and drag the image around.

 

 

Measure tool. Measures raster angles, and distances between the raster points. You can also use it to calculate the line ruling of a separation.

 

Next tool: Displays the next side result (e.g. Cover Sig 1 Front > Cover Sig 1 Back > Cover Sig 2 Front > Cover Sig 2 Back etc.). If you hold down the ‘C’ key while clicking the tool, Apogee displays the next sheet result (e.g. Cover Sig 1 Back > Cover Sig 2 Back > Cover Sig 3 Back).

 

Previous tool: Displays the previous side result. If you hold down the ‘C’ key while clicking the tool, Apogee displays the previous sheet result.

 

Turn Sheet tool. If your results have 2 sides (front and back), Raster Preview can switch between the two sides. Click this tool (Ctrl-T) to toggle the view (front or back). This tool is disabled if the result only contains one side.

 

Info tool. Display information about the selected item.

 

Light Table tool. Displays or hides blended front and back views of your raster data. This feature only works on the front and backs of the same signature/page.

 

Rule-Ups tool. Displays or hides additional layers of information on top of the Raster Preview image. The Rule/ups palette contains a table which lists the layers you can display.

 

Rotate clockwise tool. Rotates the current view 90 degrees clockwise.

 

Rotate counterclockwise tool. Rotates the current view 90 degrees counterclockwise.

 

Flip vertical tool. Flips the current view vertically.

 

Flip horizontal tool. Flips the current view horizontally.

 

Invert tool. Inverts the current view (negative).

 

Color Managed tool. Activates color-managed raster preview. This allows you to preview the rendered result using color management to convert the press color space to the monitor color space (based on ICC profiles).

 

Show/Hide rulers tool. Shows/Hides ruler coordinates in the units set in your Preferences.

 

Show/Hide grid lines tool. Shows/Hides grid lines for every major and minor division of the ruler. The default setting is specified in your Preferences.

 

Approve tool. Approves a previewed result. This tool is disabled if no soft preview has been requested.

 

Reject tool. Rejects a previewed result. This tool is disabled if no soft preview has been requested.

 

Task Processor Settings lock.

 

Edit

 

Create New

 

Delete

 

Set as default

 

Duplicate

 

Export

 

Import

 

Auto-fill (Versioning): Automatically fills the version table either with the names of the PDF layers or the names of the documents in the Page Store.

 

Insert variable

 

Approver

 

Uploader

 

Viewer

 

Candidate CSR (Customer Service Representative)

 

Preferred CSR (Customer Service Representative)

 

WebApproval account is inactive: the account exists but is not enabled.

 

WebApproval account is active: the account exists and is enabled.

 

PrintSphere account is inactive: the account exists but is not enabled.

 

PrintSphere account is active: the account exists and is enabled.

 

Press Sheet View button. Select a Press Sheet or Press Sheet side in the Press Sheet or Press nodes and click this button to open the Press Sheet View and view the selected Press Sheet side.

 

Selection tool. Use this tool to select a component or area and display its properties. This is the default tool.

 

Split Assembly tool. Use this tool to split blocks in the Assembly.

 

Repeat tool. Use this tool to repeat selected components.

 

Auto Impose button. Click this button to perform the Auto Impose task, for example after rearranging nodes or changing the properties of a Fold Sheet, Press Sheet or Press.

 

Rotate counterclockwise tool (only if Fold Sheet is selected). Rotates selected Fold Sheets 90 degrees counterclockwise on the Press Sheet.

 

Rotate clockwise tool (only if Fold Sheet is selected). Rotates selected Fold Sheets 90 degrees clockwise on the Press Sheet.

 

Flip Over tool (only if Fold Sheet is selected). Flips the front and back of the selected Fold Sheet on the Press Sheet.

 

Shows/Hides the Inspector window

 

Shows/Hides the Mark Sets Inspector window.

 

Shows/Hide the Positioning palette

 

Submit button. Submits the job with the edited imposition.

 

Close button. In the imposition windows, saves your changes and closes the imposition window. Behavior is set in the Preferences.

 

Product View button. Return to Product View from Press Sheet View.

 

Selection tool. Use this tool to select a component or area and display its properties. This is the default tool.

 

Single Instance Selection tool. Use this pointer tool to select a single instance of marks which are placed at various locations on the Press Sheet, or part of a compound mark.

 

Measurements. Use this tool to make measurements on the Press Sheet.

 

Clear Measurements (only activated if the sheet has measurements). Click to remove all measurements displayed on the Press Sheet.

 

Shows/Hides the Inspector window

 

Shows/Hides the Mark Sets Inspector window.

 

Shows/Hide the Positioning palette

 

Marks Palette button: shows/hides the Marks Palette

 

View Options Palette button: shows/hides the View Options Palette

 

Go to previous Press Sheet or web

 

Go to next Press Sheet or web

 

Turn Sheet button. In the Press Sheet View, click to view the other side of a Press Sheet.

 

Light Table.

 

Submit button. In the Press Sheet View, closes the window and submits the job without returning to the Product View.

 

Pages not assigned to signature (grey outline)

 

Pages assigned to signature (black outline)

 

Shingling applied (black arrows)

 

No shingling applied

 

Bleed (thick grey border on bleed side)

 

Glue zones (blue strips indicate non-image areas)

 

No spine (unbound product)

 

Double-sided part (unbound product - Fold Sheet node)

 

The initial node definition has been overruled (yellow background if only gutters and/or margins have changed).

 

The node contains an error that needs to be resolved.

 

Circle Mark: draws a circle with or without fill color

 

Collation Mark: stepped blocks with the signature number which are used to inspect the correct collation order of folded sheets

 

Cut Mark: a horizontal and a vertical line in the corners of a Fold Sheet to indicate the boundaries of the Fold Sheet and where it is to be cut

 

Cut-off Mark: lines at the cut-off between Web Production Schemes, on the left and right sides of the web

 

File Mark: places a specific EPS or PDF file as a mark

 

Fold Line: draws a set of vertical or horizontal lines that indicate where to fold the sheet or the page.

 

Line Mark: draws a line

 

Crop Mark: a horizontal and a vertical line to indicate where the page has to be cropped

 

Rectangular Mark: draws a rectangle with or without fill color

 

Registration Mark: draws a series of marks which are used to check that the registration of the different printing colors is correct

 

Text Mark: prints the job name, order number, color name, etc. on the Press Sheet

 

Slit Mark: draws a line to indicate where a press sheet is to be cut in ribbons for web printing

 

Density Bar: draws bars of equal density across the full width of the press sheet or along the edges.

 

Cross Mark: indicates the crosspoint of two gutters, or at the endpoint of a gutter.

 

Page Fold Line: draws a set of vertical or horizontal lines that indicate where to fold on a single page element.

 

Mark Set is always applied

 

Mark Set is only applied manually

 

Mark set is applied when all/some criteria are met

 

Mark set is applied partially (mark deleted manually for example)

 

None of the marks of the mark set are applied (marks deleted manually for example).

 

Bound product

 

Cover part

 

Plain part

 

Insert part

 

Unbound, flat, single-sided product

 

Unbound, flat, double-sided product

 

Unbound, folded, single-sided product

 

Unbound, folded, double-sided product

 

Unbound product with different part types

 

Calendar product

 

Sign and Display product

The design of the product has a contour-defining operation (other than the frame or trim-box).

The product is double-sided.

At least one of the product’s artworks was rejected. In addition, the thumbnail of the rejected artwork is shown with a red diagonal line.

At least one of the product’s artworks has remarks other than rejected.

At least one of the product’s artworks could not be aligned to the design.

At least one of the product’s artworks could not be aligned to the design with great confidence.

The product is Locked or Uniform.

The product requires vertical or horizontal Grain/Flute and there are no placed instances that violate that requirement.

The product requires vertical or horizontal Grain/Flute, but at least one placed instance violates that requirement.

The product has white content, either from the artwork or generated.

The product has varnish content, either from the artwork or generated.

The product has primer content, either from the artwork or generated.

The image is being edited via an external editor.

Indicates that full-gamut color management is applied.

‘F’ shows the effects of the rotation and mirror attributes (here shown with 90 degrees rotation and no mirroring.

Indicates a preflight report has been generated for the image.

The product has Image Operations that prevent changing the product’s size (tiling, canvas extensions, etc.).

There is a notification or snag message present on the product. The icon depicts the severity of the status: error, warning or intervention required.

 

The color will be printed/output (‘Print as’ check box selected).

 

The color will not be printed/output (‘Print as’ check box not selected).

 

The color is a process color or will be printed as a process color.

 

The color is a spot color, varnish or white.

 

The color is mapped to a color from a color book.

 

The color is taken from the application.

 

The color is mapped to a finishing operation.

 

The color is mapped to a custom color.

 

The color is mapped automatically as defined for the colors of the device.

 

The color is mapped to and depends on another color in the list.

Selection tool: To select a component or area and display its properties. This is the default tool.

Single Instance Selection tool: To select a single instance of marks which are placed at various locations, or part of a compound mark. In the Paths inspector: selects a path and its anchor points.

 

Measurements tool. Use this tool to make measurements on the Press Sheet.

 

Clear Measurements tool (only activated if the sheet has measurements). Click to remove all measurements displayed on the Press Sheet.

View Options palette button: Shows/hides the View Options palette.

Marks palette button: Shows/hides the Marks palette.

(Licensed feature) Presets: To open the Presets dialog box.

Crop image: Activates the crop mode to crop an image (Image inspector in the Product Editor).

Split tool: Activates the Split tool to split an image into tiles (Tiling inspector in the Product Editor).

Pen tool: Activates the Pen for drawing free-form paths on an image and adding/deleting points of existing paths (Paths inspector in the Product Editor).

Ellipse Path tool: Activates the Ellipse Path tool to draw ellipse and circle paths on an image (Paths inspector in the Product Editor).

Rectangle Path tool: Activates the Rectangle Path tool to draw rectangle paths on an image (Paths inspector in the Product Editor).

 

Unlocked sheet layout/frame

 

Locked sheet layout/frame.

 

Circle Mark: draws a circle with or without fill color

 

Collation Mark: stepped blocks with the signature number which are used to inspect the correct collation order of folded sheets

 

Cut-off Mark: lines at the cut-off between Web Production Schemes, on the left and right sides of the web

 

File Mark: places a specific EPS or PDF file as a mark

 

Fold Line: draws a set of vertical or horizontal lines that indicate where to fold the sheet

 

 

 

 

Line Mark: draws a line

 

Crop Mark: a horizontal and a vertical line to indicate where the page has to be cropped

 

Rectangular Mark: draws a rectangle with or without fill color

 

Registration Mark: draws a series of marks which are used to check that the registration of the different printing colors is correct

 

Station Number Mark: indicates the station of an instance of a product, i.e. its position on the sheet

 

Text Mark: prints the job name, order number, color name, etc. on the Press Sheet

 

Slit Mark: draws a line to indicate where a press sheet is to be cut in ribbons for web printing

 

Color Bar Mark: generates a bar of color patches, using the colors that are present on the press sheet (offset and wide-format) or in the product.

 

Density Bar: draws bars of equal density across the full width of the press sheet or along the edges.

 

Ink-Eater Mark: places a background mark between the products or on the outside of the fold sheets.

 

Mark Set is always applied

 

Mark Set is only applied manually

 

Mark set is applied when all/some criteria are met

 

Mark set is applied partially (mark deleted manually for example)

 

None of the marks of the mark set are applied (marks deleted manually for example).